微弧氧化Mg-3Al-1Zn镁合金应力腐蚀和腐蚀疲劳行为研究

本文主要对微弧氧化Mg-3Al-1Zn镁合金在空气和3.5 wt.%硫酸钠溶液两种环境下的应力腐蚀和腐蚀疲劳行为进行研究，并讨论其相互关系。微弧氧化处理后，Mg-3Al-1Zn镁合金的耐蚀性能得到明显改善。与Mg-3Al-1Zn镁合金基体相比，在空气中，微弧氧化后合金的应力腐蚀和腐蚀疲劳强度均下降了大约10 MPa。在3.5 wt.%硫酸钠溶液环境中，微弧氧化后合金的腐蚀疲劳性能仍然是恶化的，但是应力腐蚀强度却得到了显著改善，从58.24 MPa提高至202.08 MPa。这表明材料的力学性能（应力腐蚀和腐蚀疲劳）并不是与其腐蚀性能完全保持线性关系的。微弧氧化处理后镁合金在空气中的应力腐蚀断口为韧性断裂，在硫酸钠溶液环境中为解理断裂。而其腐蚀疲劳断口不论是在空气中还是在腐蚀环境中均为解理断裂。这主要是由于腐蚀环境和变换循环载荷的影响，两者共同作用将会加速裂纹扩展。这表明，周围环境和加载类型对材料断裂机理有重要影响。     

Unraveling the film-formation kinetics of interfacial polymerization via low coherence interferometry

Interfacial polymerization (IP) is one of the most important methods for fabricating thin film composite (TFC) membranes. Understanding the film-formation mechanisms is of great value for developing membranes with enhanced performance. This work proposed a novel method to in situ characterize the film-formation kinetics via low coherence interferometry (LCI). The polyamide film formed at the liquid–substrate interface was scanned in real time; the polymerization induced significant variations in the optical properties around the reaction zone. After mitigating the effects of the perturbed interface, the surface-averaged intensity profiles provide a solid basis for analyzing the film-formation kinetics at various depths. In particular, the effects of the monomer concentrations were investigated to reveal the asymmetric growth and development of irregular substructures. All the characterization results confirm that the LCI-based characterization is a powerful tool for studying the structural evolution of the IP layer and thereby providing deeper insights for optimizing TFC membranes.     

铝碳质长水口用低铝抗氧化涂层的研制

为抑制铝碳质长水口使用过程中石墨的氧化，其表面会涂覆含 20%~30%Al₂O₃的抗氧化涂层，但切割丝钢等特种钢冶炼过程必须严格控制钢液中夹杂的 Al₂O₃的含量，因此需要制备低氧化铝含量的抗氧化涂层。本文通过调节涂料组成、加水量和水玻璃加入量制备了低铝抗氧化涂层，并利用扫描电镜分析了抗氧化实验后试样断口的显微结构。结果表明：以粘土粉、钾长石粉和硅砂为主要原料，添加 10%硼砂的涂料可在 800 ℃形成良好的釉层，此时涂料中 A12O3的含量可降至 12%，得到了低铝涂料；当加入占涂料质量 80%的水和 40%的水玻璃时，涂层具有最佳的涂覆性能和抗氧化性能，涂层和长水口基体结合致密，保护了长水口中的石墨不被氧化。     

低剂量抑制剂Inhibex501存在下的甲烷水合物相平衡研究

含动力学抑制剂的天然气水合物相平衡研究对新型低剂量抑制剂的开发具有指导作用。在283.6 ~ 290.9 K和7.51 MPa ~ 15.97 MPa的温压范围内研究了抑制剂Inhibex501及其溶剂2-乙二醇单丁醚对甲烷水合物相平衡条件的影响。实验结果显示，0.5wt%和2.0wt%浓度的Inhibex501对甲烷水合物形成的热力学条件具有促进作用，能使甲烷水合物形成移向更高的温度或者更低的压力，而2-乙二醇单丁醚在浓度0.2wt% ~ 1.0wt%范围几乎不改变甲烷水合物形成的热力学条件，N-乙烯基己内酰胺与N-乙烯基吡咯烷酮的共聚物对水合物形成热力学条件的改变起主要作用。     

Core–shell type multi‐arm azide polymers based on hyperbranched copolyether as potential energetic materials in solid propellants

A series of novel multi‐arm azide copolymers (POGs) with the same hyperbranched poly[3‐ethyl‐3‐(hydroxymethyl)oxetane] core (PEHO‐c) and different content of linear glycidyl azide polymer shell (GAP‐s) have been synthesized by sequential cationic ring‐opening polymerization and azidation. Detailed structural information of these copolyethers was deduced from Fourier transform infrared, ¹H NMR and inverse gated decoupled ¹³C NMR spectroscopies, matrix‐assisted laser desorption ionization time‐of‐flight mass spectrometry, gel permeation chromatography and elemental analysis. The molecular weight of POG having GAP‐s and PEHO‐c with a molar ratio 14.95:1 (R_s/c) was around 31 000 g mol^?1, far above that of linear GAP (around 4000 g mol^?1). The apparent viscosity and glass transition temperature (?51 to ?23 °C) decreased first and then slightly increased with increasing molecular weight. Thermal analysis revealed that all the obtained POGs exhibited excellent resistance to thermal decomposition up to 220 °C. Moreover, the energetic properties, investigated using oxygen bomb calorimetric measurements, indicated that the enthalpy of formation of the POGs was higher than that of general linear GAP, but similar to that of branched GAP under reasonable R_s/c. The compatibilities of the POGs with common materials used in solid propellants were studied using differential scanning calorimetry and the results indicated that the POGs had good compatibility with these materials. © 2017 Society of Chemical Industry     

控锻控冷工艺对GCr15轴承钢力学性能的影响

探究不同控锻控冷热处理工艺对GCr15钢力学性能的影响,测试了它的回火稳定性、冲击性能、滚动接触疲劳寿命。结果表明,采用控锻控冷工艺可提高试样的抗回火稳定性,冲击性能提高50%以上,接触疲劳寿命提高40%以上。     

Multi-Scale Analysis of Fretting Fatigue in Heterogeneous Materials Using Computational Homogenization

This paper deals with modeling of the phenomenon of fretting fatigue in heterogeneous materials using the multi-scale computational homogenization technique and finite element analysis (FEA). The heterogeneous material for the specimens consists of a single hole model (25% void/cell, 16% void/cell and 10% void/cell) and a four-hole model (25% void/cell). Using a representative volume element (RVE), we try to produce the equivalent homogenized properties and work on a homogeneous specimen for the study of fretting fatigue. Next, the fretting fatigue contact problem is performed for 3 new cases of models that consist of a homogeneous and a heterogeneous part (single hole cell) in the contact area. The aim is to analyze the normal and shear stresses of these models and compare them with the results of the corresponding heterogeneous models based on the Direct Numerical Simulation (DNS) method. Finally, by comparing the computational time and % deviations, we draw conclusions about the reliability and effectiveness of the proposed method.     

氮含量对HPD-1双相不锈钢组织及力学性能的影响

通过显微组织观察与力学性能测试研究了氮含量(0.08%~0.22％,质量分数)对HPD-1双相不锈钢硬度、拉伸性能、低温冲击性能及疲劳性能的影响。结果表明,氮含量变化可显著影响试验钢γ/α相比例,当氮含量由0.08％升高到0.22％,γ相含量由38.1％提高至56.5％。α相的硬度由273 HV10提高到343 HV10,γ相的硬度由238 HV10提高到299 HV10,试验钢强度明显提升。氮元素对两相比例和奥氏体相韧性的双重影响导致试验钢低温冲击性能呈先上升后下降的趋势;更高的氮含量抑制疲劳裂纹萌生与拓展,是影响HPD-1双相不锈钢室温疲劳性能的主要因素。撕裂棱是疲劳断口的显著特征。     

某轻型载货车储气罐支架振动断裂分析与优化

为了有效解决某轻型载货车储气罐支架的断裂故障,首先基于建立的储气罐支架有限元模型进行振动特性分析,分析结果表明其前三阶固有频率接均处于发动机激励频率范围之外,不会产生共振。其次测试各种道路的时域载荷,测试结果表明其中角度搓板路的激励频率与储气罐支架第一阶固有频率相接近,从而引起共振,不满足振动特性要求。然后对其进行振动强度分析,分析结果表明其应力水平不达标,其最大应力点与开裂处一致。再对其进行振动疲劳寿命预测分析,分析结果表明其疲劳寿命也不达标,其危险点也与失效位置相同。再采用集成平台对储气罐支架的结构进行优化设计,优化之后其模态频率、振动强度和振动疲劳均符合性能要求,并且其重量也有所减轻,总体优化效果较佳。最后整车试验结果表明优化之后储气罐支架的振动大幅度降低,并且没有发生失效。